Round newspaper casket box

Nowadays weaving of newspaper tubes is becoming increasingly popular. Lesson is not difficult enough, besides very exciting and interesting. The cost of acquiring the source material is almost minimal, since everything that is required for the manufacture of a round casket from newspaper tubes is absolutely everyone.
To work will require:
• Old newspapers or newsprint.
• Plain knife.
• Thin needle.
• PVA glue.
• Food colorings.
• Clear varnish
• Brush for processing the finished product.
For work will be required

Step by step description of the manufacture of the box.
1. Directly weaving the casket will be made from newspaper tubes, which will require approximately 200-220 pieces. In order to get a newspaper tube, you need a newspaper or magazine, using a regular knife, cut across the page into strips whose width is about 5 cm. If you plan to have tubes of darker colors, you can use a newspaper.For tubes of light and bright colors, you should use newsprint, because when painting can appear through the letters.
with a knife

cut into strips

2. In order for the tubule to be long and neat, the needle should be used as thin as possible. On the edge of the newspaper strip fits the needle at an angle of 35-40 degrees. The smaller the angle, the thinner the tube. From thin tubes, the product turns out neater and more gentle. Tightly pressing the edge of the paper to the spoke, you need to twist the tube. The remaining upper edge to coat with white glue and tighten the tube to the end. Needle pull out. The straw is ready.
twist the straw

3. To paint the tubes, you can use the stain and food dyes.
To paint with a stain, just drop the tubes into the bottle with this solution and remove them immediately. Leave to dry in fresh air for 3 hours.
To paint the tubes with food dyes, it is necessary to dilute them according to the instructions and lower the tubes into the paint container for 5-7 seconds. Dry in a warm place until dry.
grease the edge with glue

paint it

4. To weave the bottom of the box you need 4 groups of tubes, 2 in each, put a cross - over each other. These tubules are called stanchions.
cross lay

5.Under the lowest group of tubes substitute 1 working tube and braid in turn each of the groups.
braid alternately each

6. In order to build up the work tube, it is necessary to fold one edge next in half and insert it into the work pipe. There is no need to glue it.
fold in half and insert

7. After 6-7 rows of weaving, the stanchions must be divided so that 8 single (from 4 groups) are formed. Substitute, similarly to the first, another working tube. Next, the product weave "string". To do this, you need the first working tube to clasp the stanchion from above, and the second from the bottom. The second stanchion braid similarly, only the tube that was on top, go down, and the bottom up.
the stanchions need to be divided

like this divided

braid like

8. After the bottom of the desired diameter is ready, the work tubes should be glued, and after drying, carefully cut.
glue the tubules

tubules need to glue

9. To weave the walls of the box, you must raise the stanchions. To do this, we start one stanchion from below under a nearby one and gently lift it upwards. We do the same work with the others.
lift up

one by one lift

10. If necessary, increase the number of stanchions.
racks to increase

11. Insert the form into the product. When using it, the product will be more accurate and even. Substitute 2 working tubes.
Insert the form into the product

12.Weave a “string” of 2-3 rows. In order to get a pattern, 1 work tube must be replaced with another color. Next, weave according to the intended pattern.
replace with another color

13. After the weaving of the casket wall is completed, glue and cut the work tubes.
glue the tubes

14. Bending.
Start the first stanchion from the inside for the second and go around it. The second start for the third. And so on until the end of the series.
Bending

bend

bent all

15. Next, enter the tip of the first stanchion in the formed hole, after bending around the second, next to the first. To do this manipulation with all the risers. Gently glue on the inside, and after complete drying, cut off.
do with all the pitches

complete drying trim

16. The lid trudges exactly like a bottom. At the end bend.
The lid trudges like the bottom

The cover can be decorated according to desires and imagination.
17. The finished box is varnished, which will give it shine and strength.
Round newspaper casket box

Related news

Round newspaper casket box image, picture
Round newspaper casket box 26


Round newspaper casket box 3


Round newspaper casket box 6


Round newspaper casket box 44


Round newspaper casket box 91


Round newspaper casket box 37